• Guest - w'd love to know what you think about the forum! Take the 2025 Survey »

Insight pump

M

mariposa84

Well-Known Member
Messages
127
Type of diabetes
Type 1
Hello!

Hoping someone might be able to help me.

Does anyone know how to find the Insulin to carb ratio settings on the meter? Also, the correction factor?

Thanks in advance
 
Both of these can be found in.....settings, bolus advice, time blocks. Pick the time block you want, click next a couple of times and you'll get to the carb ratio and sensitivity (correction) ☺
 
Hi @mariposa84 & thanks @noblehead for tagging
If you go to settings, bolus advice, time blocks, select a time block, then press next, next again & you'll find the carb ratio section there. Make sure you save any changes as you go along. Hope this makes sense! How are you finding it so far?
 
Thanks noblehead, fozzy84 and medusa41 for your help!!

I knew it had something to do with the time blocks...!

Struggling with trying to lower my hba1c and feeling like a failure for not being able to so hope if I tweak my ratios slightly it may help my overall control.

Thanks again☺
 
Thanks for the tag - am late to the party!

Hi @mariposa84 - don't feel like a failure - it's all a process, and you're getting your ratios sorted so that will help your control - hope it goes well. Changing just one thing at a time is a good way to go about it (I have form for being very gung ho about changes and am always tempted to change lots of things at once - with unpredictable results).

How do you like the Insight? I'm seriously in love with mine....

 
Hi @Snapsy!

Thank you for your supportive message.

Fingers crossed it works! Have just ordered a freestyle libre to see if that might help me too. Do you use one?

I really like the Insight but the one thing that drives me mad is how slow it is sometimes or when I get an electronic error and the screen freezes for what feels like forever. I was on the omnipod which I loved but the adhesive and my skin did not get on to put it mildly!
 
Hi! I know what you mean about the speed of the handset - I try to remember to turn it off once a week or so by pressing and holding the off switch for 5 seconds - that seems to make it perform better.

And yes I have a Libre - it's amazing - I couldn't be without either that or the
Insight! Sorry to hear the adhesive of the Omnipod was an issue - I fancied the Omnipod but ended up with the one the diabetes centre recommended - and that's fine because I love my pump!

 
@mariposa84 - it drives me mad too sometimes - v slow at times & always when I'm hurrying!!!! I use a libre too - can highly recommend it! @Snapsy - I'm gonna try that to speed it up -
 
I am on my second Insight pump as I was getting airbubbles in the tubing after 10 months, I have started to get them again and they are not small bubbles but 1/2 inch long some longer. I have just came off the phone to Roche and I need to speak to my Accu-Chek rep as they will not send out another pump, aprt from the bubbles I like the pump but as stated the handset cannot be compared to a mobile phone but the reboot once a week does help a little
 
Medusa41 said:
Oh no @Gaz-M - that's rubbish. Let us know what the rep says. Hope you get it sorted.
Click to expand...
Will do, I had to drop off a cartridge of insulin at the Daibetic unit tonight as it had a large airbubble in straight out of the fridge and the DSN has suggested doing a full set change every 3 days instead of the 6 days I usually have to do it but seems to me that its novonordisk that is at fault with the bubble thing as there normally is none in the new cartridges. Last night I did a full change and 20 after there was a 4mm bubble, same this morning but there was 5 smallish bubbles all of which were around 2mm
 

Try keeping the pump vertical with the tubing joining at the bottom and not at the top. That way any bubbles won't go into the tubing and will stay in the cartridge as bubbles rise to the top.
 

I found that my mdi carb ratio was a bit more correct than the ratio my pump dsn started me off on.
 
iHs said:
Try keeping the pump vertical with the tubing joining at the bottom and not at the top. That way any bubbles won't go into the tubing and will stay in the cartridge as bubbles rise to the top.
Click to expand...
yeah thats the way I wear it
 
You must log in or register to reply here.
Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn More.…