Managed it!!!!

Well done Mushy for getting the confidence to put in the steel set, I know how apprehensive you were about trying it

Jess has never had the contact detach fail. The only time we've had problems is from air bubbles in the cartridge or tubing, never had a problem with the set itself.

I can't compare about the bleeding between teflon and steel because we've only ever used steel. Sometimes it bleeds and sometimes not. Yes we remove the set completely before inserting the new one.

Well done on the steel cannula . Did you prime it before you inserted it as the steel ones need to be primed prior to insertion unlike the teflon ones which are primed once they are in.
We occasionally get a bit of bleeding but it is never much, it's normally just a little prick where it was in. I know some people have had what they call gushers but that has not been oiur experience.
We have not had a steel cannula fail yet but I suppose that nothing is ever 100%. We have been using them since December so that is a lot better than teflon ones which failed quite often.
I'm sure that if you persevere you will have fewer failures.

Harry

MushyPeaBrain said:

Also the wings don't go back down after using them. Is that on every set?

Click to expand...

I'm not sure how much your wings are not going back down. Ours don't go flat down again but they're flat enough so as not to catch on clothing. Perhaps if you took a long time to insert the cannula the wings have been held up for a longer time and more firmly (if you were nervous) so perhaps maybe that's causing a problem?

Taking the set off we use an adhesive removal wipe. Ease all the way around the cannula to unstick the sticky patch, once that is no longer sticking to your skin you can pull firmly away to whip the cannula out. I actually hold the sticky patch part rather than the wings but you'll work out what works best for you. Pull away at a 90 degree angle from your skin (as it went in i.e. straight), don't pull away just from one side causing it to come away at a sharp angle as that may cause some discomfort. We find removing the detach part first and then the cannula part is easier otherwise you have the sharp cannula poking around whilst you're trying to remove the detach part.

Bril Mushy!!

Can't help regards wings etc, as not seen your sets. I think you will find the stainless steels good, but you will have to get used to that small rigid bit of 6mm!! You can manage it, and one thing I think is that they are brillaint for a consistent performance compared to the teflons. I know I would never go back to teflon, ever. If for any reason I could not have my s-steel sets, I would NOT go back to teflon ones.

I never have any doubts nowadays whether my sets or pump or cartridges or anything are working, as since swopping to the stainless steels any high's have been totally down to me.....without doubt.

MushyPeaBrain said:

Sophia how do you manage the detach part? I have taped the little loop between the two down and the detach is sited above the cannula.

When you change how do you do it? Just detach, remove and place new one? Always before I have left the old one in so that I can make sure I position new cannula a good distance apart but it's getting busy on my stomach now with the detach bit :lol:

Also discovered that my trial set bled lots when removed, even though it was very comfy. Is this more usual with needles?

Click to expand...

Hi

When I first started to use the Rapid D I looked at Accu chek's website to see how to insert them and looked at the video link. In the beginning I used a piece of Transpore tape to go over a D shape loop but couldn't really see what the purpose was so decided to just leave the connector part loose and not use the tape. Was just wondering if you could just leave the connector bit loose and not peel off the adhesive backing?

That's true, you could just not use the connector part adhesive. We use it because if Jess drops the pump it will tug on the connector rather than the cannula part avoiding the cannula being pulled out by accident. But the adhesive sticks to well I doubt it would pull out anyway unless you pulled really hard.

We don't tape down the loop between the two sticky parts. Jess wears the site on her bottom with the connector part stuck to her tummy/hip so the loops is covered by her underwear. She's never had a problem getting it caught or hooked yet.

Yay Mushy, I'm so proud of you for getting through your phobia The more you do the set changes the more confidence you'll get, I'm sure

We don't coincide the set change with a cartridge change each time, sometimes it does happen that way but not always.

If it's just the cartridge that needs changing then we disconnect the pump from the connector part, rewind, remove the old cartridge and that end of the tubing, open a new set package and take the cartridge side of the infusion set tubing out (leaving the cannula part unused), connect the tubing to the newly filled cartridge and load into the pump, press load cartridge, then do a prime until a little squirt of insulin comes out, then plug the pump and new tubing into the connector and you're ready to go.

If it's just the cannula that needs changing then we disconnect the pump, remove the old cannula and connector sticky patch, connect the new cannula end of the tubing to the pump at the connector point (leaving alone the old cartridge tubing end), prime the pump until about five drops of insulin drip out of the cannula, insert the cannula, stick down the connector patch and you're ready to go.

I hope that makes sense. The pump rep did tell us to change the entire thing, cartridge and all, at every set change, but it seemed an awful waste of insulin so now we leave the cartridge and that end of the tubing and only replace when it gets very low.